To get the lower tang to slide out you must first:ġ. WOLFF COMPANY SHALL HAVE NO LIABILITY FOR LOSS OF USE, REVENUE OR PROFIT.To access the trigger, the lower tang must be removed. BY WAY OF EXAMPLE, AND NOT LIMITATION, THERE SHALL BE NO WARRANTIES OF MERCHANTABILITY, USE IN TRADE, OR FITNESS FOR A PARTICULAR PURPOSE. IF ANY SUCH WARRANTIES SHALL BE IMPOSED BY LAW NOTWITHSTANDING THIS PROVISION, THEN SUCH WARRANTIES SHALL BE THE RESPONSIBILITY OF W.
NO OTHER WARRANTIES OR LIABILITY WHATSOEVER, ARE EITHER EXPRESSED OR IMPLIED. THIS WARRANTY SPECIFICALLY EXCLUDES ANY AND ALL CONSEQUENTIAL OR ACCIDENTAL DAMAGES. THE REPLACEMENT OF ANY SUCH PRODUCT(S) SHALL BE W. WOLFF COMPANY’S SOLE LIABILITY THEREFOR SHALL BE THE REPLACEMENT OF ANY SUCH PRODUCT(S) THAT ARE DEFECTIVE IN MATERIAL OR WORKMANSHIP. IN THE EVENT OF ANY DEFECTS IN MATERIAL OR WORKMANSHIP, W.
WOLFF COMPANY GUARANTEES THAT ITS PRODUCTS ARE FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIP. I also include a 17185 Xtra Power Cylinder Stop Spring in this kit, Shooter's paks for Smith & Wesson K, L and N frame revolvers contain a Power Rib mainspring and 1 each of 13, 14 and 15 pound reduced power rebound springs allowing optimum adjustment of the hammer and trigger functions.Īs mentioned above, these paks can often take the place of expensive "trigger jobs" with better results NOTE: For most target and non-critical applications, Wolff recommends the TYPE-2 spring which is reduced power.įor critical applications such as law enforcement, Wolff strongly recommends the TYPE-1 spring which is factory equivalent in strength. This spring can usually take the place of expensive trigger jobs, with better results. The Wolff Power Rib Mainspring dramatically improves the smoothness and consistency of trigger pull essentially eliminating stack up as well as providing optimum hammer action. This spring has a unique variable power rib-back design. Wolff Company is a patented mainspring for use in Smith & Wesson K, L and N frame revolvers. The Power Rib Mainspring developed by W.C. Smith & Wesson Models K, L and N Shooter's Pak #17121 Free USA Shipping/Tracking ~ No Exports on this item Only ! J-Frame 17125 Spring Pak
Note: Springs will not fit and function in Bodyguard J Frame with polymer frame. Note: The Hammer Spring in this kit measures 1.650" These springs lighten trigger and let-off functions for smoother and easier trigger pull. For reference, the factory rebound spring is 18 pounds. Wolff company offers reduced power rebound springs rated from 12 to 16 pounds. These springs greatly influence the double action trigger pull which is a major concern of competitive shooters. Rebound Springs - Trigger rebound springs are common to all Smith & Wesson J, K, L and N frame revolvers. Shooters Pak - Reduced Power - This pak contains 1 each 8 pound reduced power hammer spring and 1 each 13, 14 and 15 pound reduced power rebound springs allowing adjustment for lighter and smoother trigger and hammer action. Smith & Wesson J-Frame Centerfire Revolver Note: Use this spring with the VC77TS Sear if trigger pull is too light ~ Cold Weather Hunting with Gloves
Note: Not for Centerfire M77 Target Models and Hawkeye Series and Discontinued Model 77 The Sear Spring is only a minor part, and the Wolff Spring is 40% lighter than a new stock spring, however that WILL NOT Make a 40% Difference, usually it will reduce your measured trigger pull on a new rifle by about 1/2 to 1 1/2 pound, less on an old rifle with a weaker spring.įITS Model 77 Mark I and II Long and Short Actions NOTE: The Sear Spring does not have the major effect on trigger pull, the Sear does *NOT 40% reduction in trigger pull weight
Will give an average Trigger Pull Reduction of 1/2 to 1 1/2 LbĮxcellent replacement when 100% reliability is important RUGER 77/XX Series REDUCED POWER TRIGGER / SEAR SPRINGįITS ALL Ruger 77/22 77/17 AND 77/357 77/44 77/50Ĥ0% Reduced Spring Weight* -vs- Stock Spring.